3 Signs You Should Install a Water Treatment System in Your Home

A lot of people just turn on the faucets in their homes and use the water that comes out without really thinking about it. Even though this might work for some people and in some areas, this might not be the best choice for everyone. Some homeowners can actually greatly benefit from installing water purification systems in their homes. These are a few signs that this might be something that you and your family should look into.

1. Your Family Uses Well Water

First of all, if your household uses well water, you might love the fact that you do not have to worry about paying a water bill. However, even though you might like having a well in general, you might sometimes be concerned about the quality of the water that your family drinks. This can be a very legitimate concern, but it doesn’t mean that you have to switch to water that is supplied by your local municipality. Instead, consider installing a water treatment system that will treat all of the water that comes into your home. Pairing this with testing your water regularly and keeping your well in good condition can help you ensure that your family always drinks safe, high-quality water.

2. Your Water Has a Strange Appearance or Odor

If you have found that your water has a strange appearance, such as if it has a dark hue to it, or if you don’t like the way that it smells, you might be concerned. Your first step should be having your water and your plumbing treated. Then, to help prevent further issues and to help ensure that the water that your family uses is crystal clear, clean and safe, consider installing a treatment system that will treat all of the water that enters the home. Visit the Global Hydration website to learn more, because they may be able to provide you with the information that you need.

3. Your Appliances and Plumbing Fixtures are Showing Wear and Tear

A lot of people do not realize just how much of an effect their water can have on their appliances and their plumbing fixtures. However, you should know that sinks, toilets, refrigerators and more can all be affected by mineral-rich water. If you get treat the water, however, you can make your appliances and plumbing fixtures last much longer.

As you can see, there are various ways that you can tell if you need to install one of the water treatment systems that are out there in your home. If any of these three things seem familiar to you, or if you just want to ensure that the water in your home is the best quality possible, then you may want to consider installing a water treatment system. Luckily, you might find that this will be more affordable than you think.

Improving Your Pump Packing’s Performance through Proper Installation

Pump packing is widely employed for high shaft speeds. It contains lubricants that are specially formulated to aid on pump equipment’s start up, ensuring packing pliability for more durability. Pump packing is necessary for reducing leakage into the atmosphere through sealing the rotating shaft used in a stationary housing.

When using a packed pump, properly unpacking, installing and adjusting it can potentially make all the difference between success and failure of your pump.

Removing Pump Packaging

Removing all the old pump packing can be among the most challenging steps in the pump packing process. When a system outage occurs, repacking equipment is often done under severe time constraints. Resisting the urge of simply removing just a couple of package rings located near the stuffing box is important. Rather, go all the way to the bottom.
If your pump is using a lantern ring and flush injection, ensure that the lantern ring is removed as well as the packing beneath it. The Engineer needs to take care in terms of ensuring that the shaft as well as the bore surface is not damaged during the process.

Inspecting the Packaging

For the Engineer and engineering team, the opportunity of peeping inside the pump stuffing box doesn’t happen on many occasions. They should maximize on this chance to check and inspect the condition of the equipment and also undertake some record keeping. This will make the process of unpacking, installing or servicing easier the next time.

Measure and Record

Products being shipped to Canada have to be in conformity with the relevant set standards. Dimensions like stuffing box diameter and depth as well as the shaft diameter need to be carefully measured and recorded by the Engineer in charge.

If your pump uses flush injection, the flush port location and the lantern ring length should also be measured and duly recorded. These are the measurements that will assist in properly aligning the lantern ring with the flush port. If in the past your pump has proven to be inconsistent, this could perhaps be the required solution.

Installing the Pump

As each ring gets inserted, it’s important that it gets firmly seated into the stuffing box bottom before the next ring is installed. This creates more consistent compression throughout the packing.

For tamping, the engineering team doing the installation can employ short lengths of metallic bushings, split tubing, or corrugated cardboard. Remember to have these tools removed prior installing the next ring! The seam of successive rings should be offset by 90 degrees.

Conclusion

Proper pump installation makes all the difference between success and failure of your pumping equipment. By keeping in mind the fine points discussed above during the entire procedure, the chances of success are greatly increased.Only then can you realize a reliable, robust, long lasting seal.

Tips To Save Money With Flexographic Printing Sleeves

Having good flex storage solutions for your business will guarantee a long lasting working of the flexographic sleeves and in the process save money in the long run. Investing in flexographic printing could be so costly, and there is a need to ensure in everyday printing process there is a way of maintaining costs at mining so that you can recoup the return on investment in the shortest time possible.

Cleaning the Plates

The first tip is to ensure the flexo plates are always clean. Printing process could sometimes be a dirty job because of the inks, solvents, and oils involved in the process. To ensure the plates are always in good working conditions, and working with maximum efficiency, there should be routine maintenance and cleaning. Proper caring of the cutting plates will result in cost saving in the long-term and will reduce the number of plates bought for replacement.

The plates should always be cleaned immediately they are removed from the cylinder. Regular and proper care of the plates will lead to improved plate performance over a long time. Ensure there are no ink on the plates and do not postpone the cleaning, you need to act as soon as possible, and this will be good for your printing business in the long run. If the plate is not clean at the start of the printing job, particles could easily get trapped under the ink and might be impossible to remove later. Therefore, ensuring that ink and residues are removed before running the machine will always provide the best possible transfer of ink.

Cleaning of the Sleeves

Flexography printing often requires routine cleaning of the sleeves to print clean and bright lines. Therefore, cleaning has to be done as quickly as possible to remove ink, oil, and any other residues. Close attention needs to be observed to ensure the ends and the insides of the sleeves are kept as clean as possible. Investing on the best flexstand provides a quick cleaning of all the flexographic sleeves within the printing press without the need to move out. Flexcart is also necessary for smooth movement within the room from one point to another to save time and improve efficiency. It would be costly to run the printing process with dirty sleeves, and it will shorten their lifespan. Using the right cleaning solutions as prescribed by the manufacturer is paramount; never use any product just because it is cheap in the long run that will be very expensive. Using acid, salt solution, or alkaline will damage the surfaces of the sleeves.

Storing

All flexographic sleeves should be kept in their protective covers to work for a long time only when they are completely dry. A compressed air drier may be used to ensure there is no water or residues in the sleeves before they are stored. Investing on a vertical flexstand to store flexographic sleeves is crucial to have them working for a long time. Horizontal storage system would leave the sleeves bent and remain in an oval shape because of the strain from gravity.